Liebherr HC1080 Instalační manuál

InstallationInstructionsCombined fridge-freezer forintegrated use, door-on-doorHC 10..081116 7086366 - 00

Fig. 12 CAUTIONHinges are spring-loaded and can cause pinching injuries!uLeave hinges open.uRemoving the door: Push the door forward and theno

Fig. 14 uSwap the fixing bracket to the opposite side.Fig. 15 uFitting the door again: Reattach the door to the hingesand tighten the screws.Fig. 16 u

2.8 Water connection*WARNINGElectrical Shock Hazard!uDo not make the water connection while the applianceis connected to an electrical outlet.uDiscon

Fig. 19 uAffix the water supply Fig. 19 (7) to the housing, ifnecessary, using the locking element Fig. 19 (10).Before fitting into the cabi

Fig. 20 The following tools are supplied with the appliance:Fig. 21 The following tool is also required:Fig. 22 If the depth of the unit isless than

Fig. 25 uFitting spring steel brackets. If the fridge section door islarge use two pairs of spring steel brackets.Fig. 26 Fig. 27 With 5/8 in. (16 mm)

uFit the equalizer trim to the top of the appliance. If thehinge is on the left, slide the equalizer trim into the righthook. If the hinge is on t

Fig. 32 uPush the appliance in until the handle side above thebracket and below the stop meets the front of thecabinet side panel.

Fig. 35 uTo fix the appliance in the recess: first hinge side up,then down, then in the middle. Then handle side downand finally handle side

Fig. 37 uSupporting the appliance at the bottom at the back:Insert the handle into the stabilization rail and push thestabilization rail int

Contents1 General safety information... 22 Start-up... 22.1 Transporti

Fig. 42 uRemove the fitting aids, turn round and insert into theadjacent opening.Fig. 43 uClip the cover on the crosspiece on the handle side

Fig. 47 uAlign the front edge of the spring steel bracket parallelto the unit door edge and screw the bracket downtightly.Fig. 48 uAligning

Fig. 52 Check the following points to make sure the appliance isinstalled correctly. Otherwise, icing up, the formation ofcondensate and malfu

Start-up* Depending on model and options 23

For Service in the U.S.:Liebherr Service CenterToll Free: 1-866-LIEBHER or [email protected] Solutions, Inc.3501

WARNINGRisk of fire due to refrigerant.The refrigerant contained within the appliance, R 600a, isenvironmentally friendly, but flammable. Leaking

2.3 Appliance dimensionsFig. 1 in. mmA22 in. 559 mmB21 7/16 in. 544 mm C69 11/16 in. 1770 mm D27 3/8 in. 695 mmE5/8 in. 15 mm2.4 Recess dimensionsTh

uAlign the cabinets with a spirit level and a try square. Ifnecessary level them by putting something underneaththem.uEnsure that the floor and the si

Fig. 3 The height of the freezer door is 24-24/32 in. (629 mm).uIn order to cover the bottom section of the appliance:extend the plate height

uTotal height of the cupboard (i.e. 70-3/8 in. (1788 mm))plus thickness of the cover and floor plate (normally3/4 in. (19 mm)) minus the heigh

Ventilation from underneath through the floor of thekitchen cabinet can be set up with the supplied ventilationgrid Fig. 7 (3) or an air vent w

Fig. 10 uRemove covers.Fig. 11 uUndo the screws on the hinges but do not removethem.Start-up* Depending on model and options 9